I’ve always loved being a plumber because it’s a very interesting three dimensional challenge to install plumbing, drain and vent piping in a new house or in a major remodel. Being also the lead carpenter and builder on my jobs allowed me to think ahead to make sure all the frames and raw wood were installed so it didn’t have to be butchered to get into the pipes.

Last month, Amanda, who lives in South Carolina, reached out to me. She wanted to know how she could get money from the original plumber who installed the plumbing in her house. Amanda received bad advice from another plumber or remodeler who told her a toilet drain pipe was installed incorrectly by the original plumber.

Amanda paid the new plumber to cut out the perfectly fine pipes and install new ones with smoother bends in them. Too bad she wasted so much money! She could have spent less than $50 and scheduled a simple phone call to see if she could get any good advice. But that’s water over the dam.

Here was Amanda’s situation. The toilet drain pipe ran about 5 feet between two floor joists. It was then turned down with a regular 90-degree connector — some call it a short bent L — and immediately connected to a curved 90-degree connector rotated 90 degrees to allow the toilet waste to continue its journey to the sewage treatment plant below Floor joists, but now perpendicular to the joists.

She was told that the short 90 was inappropriate. I asked her if she had ever had constipation in the eight years since the house was built. Her answer was no. That’s why she never had constipation. The short 90 degree fitting is similar to the exact change in direction of the toilet drain that it would encounter if the pipe were connected to a standard tee fitting. Plumbers have installed horizontal toilet drainpipes connected to tees for many decades.

When you flush the toilet, the water and waste flow straight down and immediately hit a 90 degree fitting under the toilet flange. This 90 degree fitting directs the water horizontally toward the tee that is maybe 1 or 2 feet away. When the sewage reaches the middle of the tee, it makes a sharp turn and flows back down. Imagine a river flowing over a waterfall. This is a perfectly acceptable configuration – after all, it has worked well for Mother Nature for millions of years.

Rip out the plaster or drywall and you’ll find this exact configuration in millions of homes and buildings across the United States. Plumbers have used tees since the early 1900s and still use them today. In fact, I used this exact configuration two years ago when I recorded my video on flushable wipes.

In many situations, the vertical pipe exiting the bottom of the tee is just a vertical stack. This pipe could be 8 or 9 feet tall. Think of a sanitary fireplace as a chimney. Sewage goes down the chimney while smoke goes up a chimney.

At the bottom of the stacks it is best to install a Sweep 90 fitting. These fittings have a slightly larger radius than a short 90 fitting. The longer radius is very friendly to pipe cleaning snakes. This is exactly why plumbers have been using Sweep 90 fittings for decades.

In Amanda’s situation, she had an acceptable piping setup. It’s just that her stack was only 3 inches tall. Nothing wrong with that. I’ve done this before where I needed to tuck a horizontal drain pipe against floor joists in a basement or crawl space. I’ve never had problems with constipation.

It’s possible that Amanda misunderstood the advice that was given to her, or that the plumber who gave the advice wasn’t clear. Any direction change fittings routed under a ceiling should not have 90 degree fittings. If you need to change direction under concrete or other underground pipe conditions, e.g. B. in a sewer line, use two 45 degree fittings. Best practice is to separate the 45 degree connectors by at least 6 inches if possible. This is a tool for draining cleaning snakes.

You can have a 90 degree faucet under a slab, but it must either be at the bottom of a stack, as I described earlier, or it can be under a toilet that sits on a slab. If a clog occurs in either of these locations, it is usually cleared by installing a cleaning tee just above the base of the chimney, or removing the toilet to inspect the 90 degree fitting.

If you want to learn more about plumbing drain lines or the mystical plumbing vent lines, I have several videos for you on my website, askthebuilder.com. Simply enter “sanitary videos” into the search engine there. If you have questions about your drainpipes, look for the Ask Tim navigation link and enter your question for me. I’m happy to help you save time and money.

Subscribe to Tim Carter’s free newsletter and listen to his new podcasts at askthebuilder.com.

The post Ask the Builder: Putting in plumbing drain pipes appeared first on Los Gatos News And Events.

Air conditioners on a roof of the industrial building with blue sky and clouds in the background. https://shp.com/2018/08/07/designing-hvac-systems-to-last-in-schools/

This article was written by Emergency Air, an Arizona-based AC service and repair company.

A commercial building these days is hard to imagine without a good HVAC system. As the climate becomes more extreme and unpredictable, it only makes economic sense for anyone who owns and operates a commercial building to ensure the comfort of the people who work, do business and shop there.

There are several things to consider when looking for a new HVAC system for your commercial building in the market. Here are some of those critical factors that need to be considered in your advertising HVAC installation.

The costs

Given the upfront cost of a commercial HVAC unit and its installation, it is normal for a building owner or manager to be tempted by the cheapest option. However, a cheap commercial HVAC system is likely to have more than a few drawbacks, from a much shorter lifespan to poor performance. However, that doesn’t mean you should buy the most expensive system on the market. Just make sure you are getting quotes from multiple HVAC contractors so you can make the necessary comparisons for life, performance and system efficiency, among other things.

The size of the building

The larger the building, the higher the comfort requirements. Make sure you choose an HVAC system that is the right size for the building so that residents and visitors are comfortable whatever the weather. If you install one that is too small for that, expect higher energy costs as your HVAC unit will work harder and longer to keep everyone cool. If the HVAC system you choose is oversized, the entire building will be cooled and heated inconsistently due to the frequent short cycles. It will also be difficult to dehumidify the air with the much shorter on and off cycle.

To get the right HVAC system for your commercial building, contact your trusted HVAC contractor who will perform a load calculation to assess the size of your property and its other properties, as well as cooling and heating needs. If you operate a large system, you can also use the load calculation of an air conditioning system to determine whether you need more than one heating or cooling system for it.

The type of HVAC system you need

Commercial HVAC systems come in a variety of brands and models including:

• Single split systems– A single shared HVAC system is known as such because it is “split” into two main components: the condensing unit, which contains the compressor, condenser and condenser fan, and the ventilation unit, which houses the expansion device, evaporator and fan Evaporator fan. Single-split systems are compact and cheaper to install than a central system. They take up less space, making them ideal for small offices, shops, cafes and restaurants.
• Multi-split systems– While a single split system consists of a compressor and an air outlet, a multi-split system usually uses a single larger outdoor unit to power up to four indoor units. This setup allows a multi-split system to cool multiple rooms at the same time, making it perfect for larger commercial spaces such as retail stores, offices, and doctor’s offices with multiple walls and floors. Even if you are connected to a single outdoor unit, you can operate and control each indoor unit independently with its own remote control.
• VRF systems (variable refrigerant flow)– Unlike traditional HVAC systems, VRF (Variable Refrigerant Flow) units use refrigerant lines instead of lines to cool or heat rooms in a commercial facility. What makes them a great choice for commercial buildings is that VRF systems are highly efficient and can achieve energy savings of up to 30% to 40%.

Contact your HVAC contractor to find out what type of commercial HVAC system will best fit the landscape of your building.

The current status of your sewer system

Does your building have a central management system that has been in place for years?

If so, you might want to have one HVAC technician Check the current status before installing your new heating and cooling system. After all, old ducts are more likely to have leaks, making your HVAC operation inefficient and therefore costly to you. If your plumbing is causing problems, your HVAC technician can recommend any repairs, adjustments, or renovations needed before proceeding with the installation of your new HVAC system.

The geographic location of your building

It is possible that your building will heat or cool in a certain way due to its geographic location. Regardless of whether the location of your building on the map is intentional or totally unintentional, you should still opt for an HVAC system that can handle the heating and cooling functions associated with its location. If you don’t take into account the geographic location of your building and its heating or cooling effects, your HVAC system could run inefficiently throughout its life. When choosing a new commercial cooling and heating system, always make sure that you are only working with HVAC contractors that you can trust. This is the only way to get the right HVAC system for your commercial building.

The post Key Issues When Putting in A Business HVAC System appeared first on Los Gatos News And Events.